Ionic Layer Research Articles

In-Situ Construction of Electronically Insulating and Air-Stable Ionic Conductor Layer on Electrolyte Surface and Grain Boundary to Enable High-Performance Garnet-Type Solid-State Batteries.

Lithophobic Li2CO3/LiOH contaminants and high-resistance lithium-deficient phases produced from the exposure of garnet electrolyte to air leads to a decrease in electrolyte ion transfer ability. Additionally, garnet electrolyte grain boundaries (GBs) with narrow bandgap and high electron conductivity are potential channels for current leakage, which accelerate Li dendrites generation, ultimately leading to short-circuiting of all-solid-state batteries (ASSBs). Herein, a stably lithiophilic Li2ZO3 is in situ constructed at garnet electrolyte surface and GBs by interfacial modification with ZrO2 and Li2CO3 (Z+C) co-sintering to eliminate the detrimental contaminants and lithium-deficient phases. The Li2ZO3 formed on the modified electrolyte (LLZTO-(Z+C)) surface effectively improves the interfacial compatibility and air stability of the electrolyte. Li2ZO3 formed at GBs broadens the energy bandgaps of LLZTO-(Z+C) and significantly inhibits lithium dendrite generation. More Li+ transport paths found in LLZTO-Z+C by first-principles calculations increase Li+ conductivity from 1.04×10-4 to 7.45×10-4Scm-1. Eventually, the Li|LLZTO-(Z+C)|Li symmetric cell maintains stable cycling for over 2000h at 0.8mAcm-2. The capacity retention of LiFePO4|LLZTO-(Z+C)|Li battery retains 70.5% after 5800 ultralong cycles at 4C. This work provides a potential solution to simultaneously enhance the air stability and modulate chemical characteristics of the garnet electrolyte surface and GBs for ASSBs.

A Novel Bismuth‐Rich Bi3O4Cl/BixOyIz Composite with Intensified Photocatalytic Internal Electrical Field for Photocatalytic Degradation of Antibiotics

The enhancement of photocatalytic semiconductor degradation performance through a bismuth‐rich strategy and heterojunction engineering is considered a very effective approach. Herein, the bismuth‐rich Bi3O4Cl/BixOyIz composites are synthesized through a simple solvothermal reaction. The composites have an internal electric field because of their specific layered structure. Due to the difference between their covalent [BixOy]2+ layer and exchangeable halogen ion layer, the enhanced internal electric field facilitates electron transfer at the high‐quality interface of the semiconductor. The trace presence of Bi3O4Cl/BixOyIz (0.1 g L−1) can achieve an 88% removal of tetracycline (20 mg L−1) from the solution phase under visible light illumination in 120 min. The photocatalytic activity is much higher than that of pure BiOCl and BiOI. Furthermore, the material also exhibits high photocatalytic degradation performance for bisphenol A, doxycycline hydrochloride, etc. The excellent results further confirm the application range of the prepared photocatalysts. The superior photocatalytic activity of Bi3O4Cl/BixOyIz is attributed to the formation of a heterojunction and the generation of an internal electric field, which enhances charge separation and oxidation ability. Photoelectrochemical characterization can confirm the above views. Free radical trapping experiments and electron spin resonance show that heterojunctions can produce abundant •O2− and •OH under visible light irradiation.

A Study of Nanostructured FeO Thin Film-Based Allure Red and Direct Blue 15 Azo Dyes Sensing Scheme

This study reports on the amperometric sensing properties of FeO/Fe2O3 thin films for the detection of Allura Red (AR) and Direct Blue 15 (DB15) Azo dyes. The FeO/Fe2O3 thin films were produced using the Sequential Ionic Layer Adsorption and Reaction (SILAR) method and Na+-doping. The morphological and structural properties of the nanocomposites produced at pH of 10.5 showed good properties for the detection of azo dyes. The linear curve fit equations for AR and DB15 droplet applications onto Na+-doped FeO nanocomposite thin film samples were found to be y = -0.0002x + 0.0043 (R² = 0.9143) and y = -7E-05x + 0.0005 (R² = 0.9809), respectively. The findings reveal that adding Na+ doping to FeO/Fe2O3 thin films can effectively increase the detection response for the target azo dyes and enhance the sensitivity of the sensing system. The results suggest that the SILAR method can be used to produce low-cost and reusable FeO/Fe2O3 thin film devices, which can be promising candidates for the detection of toxic azo dyes in liquid samples.

Sustainable and cyclic synthesis of 2D Co(OH)2 nanosheets for scalable production of high-performance electrocatalysts

Ultrathin 2D nanomaterials with extremely large surface area and unique electrochemical properties are considered excellent electrocatalyst candidates for clean energy conversion and environmental applications. However, it is still challenging to prepare 2D catalysts through a scalable and sustainable process that may become suitable for industrial demands. Here, we reported a facile cyclic synthesis method of ultrathin 2D nanomaterials based on the ionic layer epitaxy. By repeatedly refreshing a surfactant monolayer on the solution surface, free-standing 2.2 nm thick hexagonal Co(OH)2 nanosheets were obtained from the water surface at ambient conditions in multiple cycles. These nanosheets exhibited a consistently high OER performance with an average overpotential of 427.4 ± 5.3 mV at 10 mA cm−2. Remarkably, hexagonal NSs could be obtained from a wide range of precursor concentrations which could enable over 84 cycles of synthesis on the same stock precursor solution. It will shed light on the design of autonomous and sustainable synthesis of 2D nanomaterials for advanced electrocatalysis development toward a clean future.

Growth kinetics of novel nickel oxide (NiO) nano fibers on glass substrates by SILAR process: A solution to remove AZO dye

This article presents the growth of uniformly distributed nickel oxide (NiO) nanofibers on a glass substrate by the Successive Ionic Layer Adsorption and Reaction (SILAR) process and explores its photocatalytic features towards an AZO dye. The nanofiber grown by the SILAR process is subjected to annealing at 400°C to decompose the hydroxide group into oxide. X-ray diffraction pattern divulges the Face-Centered Cubic (FCC) structure of NiO, and its average crystallite size (46–61 nm). The fibrous morphology with the width varying from 37.83 to 42.05 nm is confirmed through FESEM micrographs. The existence of nickel and oxide, with atomic percentages in the ratio 40:60 is confirmed by EDX analysis. From the UV–visible spectrum, the band gap energy Eg is determined using a Tauc plot and the values are varied between 3.38 eV and and 3.41 eV. Photocatalytic degradation efficiency for the Congo red dye is found to be 93% for reusable NiO nanofibers under the illumination of UV light. The photodegradation pathway of Congo red dye is presented based on gas chromatography-mass spectrometry (GC-MS) analysis. The prospective applications of the current work in wastewater treatment make it significant.

SILAR Growth of ZnO NSs/CdS QDs on the Optical Fiber-Based Opto-Electrode with Guided In Situ Light and Its Application for the "Signal-On" Detection of Inflammatory Cytokine.

In this study, a novel integrated photoelectrochemical (PEC) sensor platform was proposed, utilizing an optical fiber (OF) as the working electrode for guided in situ light. A CdS quantum dots (QDs)/ZnO nanosheets (NSs) n-n heterojunction was quickly and easily constructed on the OF surface by successive ionic layer adsorption and reaction (SILAR). Au nanoparticles (NPs)@dsDNA as a capturing probe were modified on the CdS QDs/ZnO NSs@OF (CZ@OF). Due to the energy transfer between Au NPs@dsDNA and CdS QDs, the resultant opto-electrode has a lower background near zero, enabling the "signal-on" detection of biomarkers (interleukin-6 (IL-6) as a model). The OF-PEC biosensor demonstrated a wide linear range from 1 to 100 pg mL-1 with a regression coefficient (R2) of 0.9958 and an impressive detection limit (LOD) of 0.19 pg mL-1. More significantly, the proposed OF-PEC can be successfully used for the detection of IL-6 in serum samples from patients with pulmonary arterial hypertension, and it showed consistency and is more sensitive to trace concentrations compared to BD FACSCanto II flow cytometry used at the hospital. This holds significance for an early disease diagnosis. Therefore, the proposed OF-PEC not only achieves integration of the light source and sensing interface but also enables sensitive and accurate "signal-on" detection of IL-6. Furthermore, due to the flexibility and remote detection capabilities of OF, the application of OF-PEC is expected to be expanded more widely. This approach opens up possibilities for advances in PEC sensing.

Stabilizing Solid Electrolyte Interphase on Liquid Metal Via Dynamic Hydrogel-Derived Carbon Framework Encapsulation.

Eutectic gallium-indium liquid metal (EGaIn-LM), with a considerable capacity and unique self-healing properties derived from its intrinsic liquid nature, gains tremendous attention for lithium-ion batteries (LIBs) anode. However, the fluidity of the LM can trigger continuous consumption of the electrolyte, and its liquid-solid transition during the lithiation/de-lithiation process may result in the rupture of the solid electrolyte interface (SEI). Herein, LM is employed as an initiator to in situ assemble the 3D hydrogel for dynamically encapsulating itself; the LM nanoparticles can be homogeneously confined within the hydrogel-derived carbon framework (HDC) after calcination. Such design effectively alleviates the volume expansion of LM and facilitates electron transportation, resulting in a superior rate capability and long-term cyclability. Further, the "dual-layer" SEI structure and its key components, including the robust LiF outer layer and corrosion-resistant and ionic conductive LiGaOx inner layer are revealed, confirming the involvement of LM in the formation of SEI, as well as the important role of carbon framework in reducing interfacial side reactions and SEI decomposition. This work provides a distinct perspective for the formation, structural evolution, and composition of SEI at the liquid/solid interface, and demonstrates an effective strategy to construct a reliable matrix for stabilizing the SEI.

Simple and affordable synthesis of a binder-free nickel-zinc sulfide electrode for high-performance supercapacitors

Due to the increasing demand for renewable energy solutions, aqueous energy systems have emerged as promising and sustainable technologies. Nanostructured transition metal sulfides, renowned for their exceptional properties, are prime candidates for electrochemical supercapacitors. In this study, we present the synthesis of nickel-zinc sulfide (Ni-Zn-S) as a binder-free supercapacitor material using the affordable successive ionic layer adsorption and reaction simple technique. The active nanomaterial was directly deposited onto a 3D Ni foam current collector substrate, negating the need for a binder. The synergistic combination of Ni and Zn enhances the electrode capacitance. Various electrochemical techniques were used to evaluate the loaded active material as a binder-free supercapacitor electrode in a 6 M KOH electrolyte. Results indicate pseudocapacitive performance, achieving a high specific capacitance of 400F/g at 0.7 A/g. This material retains 97 % of its capacity, even after 2000 cycles, showcasing exceptional long-term cycling stability. These findings underscore the potential of the Ni-Zn-S electrode for delivering low-cost, high-performance supercapacitors.

Synthesis, Characterization and Power Factor Estimation of SnSe Thin Film for Energy Harvesting Applications

In this work, a simple, cost-effective successive ionic layer adsorption and reaction (SILAR) deposition technique has been used to deposit a high-quality tin selenide (SnSe) thin film onto a glass substrate. Structural, morphologic, and thermoelectric properties have been characterized for the prepared thin film. X-ray diffraction (XRD) results of the SnSe thin film reveal an orthorhombic structure phase. The morphological properties of the prepared thin films have been studied using field emission scanning electron microscopy (FESEM). The stoichiometric composition of the deposited thin film and the elemental binding energies of the Sn and Se elements have been investigated with energy-dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The Fourier transformation infrared (FTIR) spectrum of the SnSe thin film displays vibrational modes of chalcogenides bonds. These results suggest that the developed thin film is crystalline, uniform, and without impurities and is appropriate for energy harvesting applications. The prepared thin film’s Seebeck coefficient and electrical resistivity were estimated through ZEM-3 from room temperature to 600 K. The power factor was evaluated. A substantially high electrical conductivity is observed, which decreases somewhat with temperature, suggesting a semimetal conducting transport—the absolute values of the Seebeck coefficient increase with temperature. The resulting power factor showed the highest values near room temperature and a somewhat decreasing trend as the temperature increased. Despite lower values of the Seebeck coefficient, the substantially enhanced power factor is due to the higher electrical conductivity of the thin film, superior to that reported previously. This precursor study demonstrates promising results for developing high-performance flexible thermoelectric devices via a simple and facile SILAR strategy.

Anodized TiO2 Nanotubes Sensitized with Selenium Doped CdS Nanoparticles for Solar Water Splitting

In this research, TiO2 nanotubes (NTs) were produced by electrochemical anodization of a Ti substrate where different NH4F wt.% in the electrolyte was added. NTs with diameter of 65–90 nm and 3.3–4.9 µm length were obtained and sensitized with binary cadmium chalcogenides nanoparticles, CdS and CdSe, by successive ionic layer adsorption and reaction method (SILAR). Additionally, both anions S and Se were deposited onto Cd, labeled as CdSSe and CdSeS, to evaluate the effect of the deposition order of the anion from the precursor solution to form cadmium chalcogenides. The structural, optical, and electrochemical performance were analyzed through the SEM, XRD, XPS, UV-VIS, lineal voltammetry and chronoamperometry characterizations. The increase of NH4F wt.% from 1.5% to 4.5% produced a decrement of the diameter and length attributed to the fluoride ions concentration causing solubility of the NTs. XRD confirmed the TiO2 anatase and hexagonal CdS structures. From the EDS and XPS results, the presence of small amount of Se in the sensitized samples demonstrated the doping effect of Se instead of forming ternary semiconductor. With the sensitization of the TiO2 NTs with the nanoparticles, an improved hydrogen generation was observed (reaching 1.068 mL h−1 cm−2) in the sample with CdSSe. The improvement was associated to a synergetic effect in the light absorption and higher cadmium chalcogenide amount deposited when sulfur ions were deposited before selenium.

Copper-Enriched Nanostructured Conductive Thermoelectric Copper(I) Iodide Films Obtained by Chemical Solution Deposition on Flexible Substrates

The objects of our research are flexible thin-film thermoelectric materials with nanostructured CuI layers 0.5–1.0 μm thick, fabricated by the chemical solution method Successive Ionic Layer Adsorption and Reaction (SILAR) on flexible polyethylene terephthalate and polyimide substrates. These cubic γ-CuI films differ from films obtained by other chemical solution methods, such as spin-coating, sputtering, and inject printing, in their low resistivity due to acceptor impurities of sulfur and oxygen introduced into CuI from aqueous precursor solutions during SILAR deposition. Energy barriers at the boundaries of 18–22 nm CuI nanograins and a large number of charge carriers inside the nanograins determine the transport properties in the temperature interval 295–340 K characterized by transitions from semiconductor to metallic behavior with increasing temperature, which are typical of nanostructured degenerate semiconductors. Due to the resistivity of about 0.8 mΩ· m at 310 K and the Seebeck coefficient 101 μV/K, the thermoelectric power factor of the CuI film 1.0 μm thick on the polyimide substrate is 12.3 μW/(m · K2), which corresponds to modern thin-film p-type thermoelectric materials. It confirms the suitability of CuI films obtained by the SILAR method for the fabrication of promising inexpensive non-toxic flexible thermoelectric materials.

Modeling the Electric Double Layer at the Liposome Vesicle via Classical Density Functional Theory: Solution of Poisson's Equations for Curved Membranes.

The electric double layer at the liposome vesicle membrane has been investigated by a modified fundamental-measure theory in the framework of the restricted primitive model. An analytical equation has been obtained for the mean electrostatic potential (MEP) by solving Poisson's equation for curved membranes. This study investigates the influence of vesicle size, membrane thickness, surface charges, and electrolyte concentration on the structure, composition, and width of electric double layers (EDLs) on the inner and outer membrane walls. Our findings indicate that a thin and denser layer of ions is formed at the concave wall of the membrane (inner wall) compared to that at the outer membrane. As expected, the width of the diffuse layer decreases with the concentration and surface charge. Also, when the surface charges on both concave and convex walls are the same, the absolute value of MEPs on the inner membrane, concave wall, is greater than that on the convex wall. We have also investigated the diffuse potential, which decreases with concentration, membrane thickness, and cavity size, whereas it increases with surface charges. As we expect, the contact density of counterions at the inner concave wall of the vesicle cavity is always greater than the corresponding value at the convex wall, whereas this trend reverses for co-ions. Also, the contact density of counterions (co-ions) at the inner wall decreases (increases) with cavity size, whereas it increases at the outer wall (decreases). Finally, depletion of co-ions occurs at the membrane walls with enhancement in surface charges.

Synthesis, Optical, Dielectric, SHG, Magnetic and Visible Light Driven Catalytic Studies on Compounds Belonging to the Swedenborgite Structure.

A new compound, InBaZn3GaO7, with swedenborgite structure along with transition metal (TM) substituted variants have also been prepared. The structure contains layers of tetrahedral ions (Zn2+/Ga3+) connected by octahedrally coordinated In3+ ion forming the three-dimensional structure with voids where the Ba2+ ions occupy. The TM substituted compounds form with new colors. The origin of the color was understood based on the ligand-field transitions. The near IR reflectivity studies indicate that the Ni - substituted compounds exhibit good near - IR reflectivity behavior, making them possible candidates for 'cool pigments'. The temperature dependent dielectric studies indicate that the InBaZn3GaO7 compound undergoes a phase transition at ~360 °C. The compounds are active towards second harmonic generation (SHG). Magnetic studies show the compounds, InBaZn2CoFeO7 and InBaZn2CuFeO7 to be anti-ferromagnetic in nature. The copper containing compounds were found to be good catalysts, under visible light, for the oxidation of aromatic alkenes. The many properties observed in the swedenborgite structure-based compounds suggests that the mineral structure offers a fertile ground to investigate newer compounds and properties.

Effective development and utilization of SILAR-assisted TiO2 and CsPb2Br5 nanocomposites for photochemical and biological cleaning of environment

Recently, cesium lead halide perovskites such as CsPb2Br5 and CsPbBr3 have drawn the attention of researchers because of their unique optical, electronic, and chemical properties. To improve the photo and/or chemical performance of such CsPb2Br5 (termed as CPB hereafter), we have realized multiple facile routes for its combination with UV-active TiO2 nanoparticles. Resultantly developed binary nanocomposites of TiO2, CPB perovskites and TiO2/CPB-nanocomposite (TiO2/CPB-NC) offered a meaningful photochemical contrast between pseudo-successive ionic layer adsorption and reaction (p-SILAR) and electrostatic self-assembly methods for targeting photocatalytic degradation of toxic dyes under solar irradiation and resulted significant performance as reactant for oxygen evolution (OER) as revealed by extensive electrochemical impedance spectroscopy (EIS). In parallel to extensive material-based characterization using SEM, XRD, and UV Vis. etc, the study was further extended to the theoretical investigation of the structure of CsPb2Br5, and antibacterial activity against gram-positive and gram-negative bacteria namely Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus). RhB degradation of TiO2 increased from 13% to 58% by deposition of CPB, in parallel to 100% inhition zone growth.

Impact of Co:Fe cations composition in amorphous and mesoporous cobalt iron phosphate electrocatalysts synthesized by SILAR method on durable electrochemical water splitting

Efficient and durable electrocatalysts are crucial for energy conversion devices that perform the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER). The structural and morphological characteristics of the electrocatalyst can significantly impact the HER/OER performance. Therefore, it is essential to develop a high-performing electrocatalyst with desired properties using a simple and cost-effective chemical process. So, herein, successive ionic layer adsorption and reaction (SILAR) deposited amorphous, hydrous cobalt iron phosphate (CFP) thin film electrocatalysts are implemented toward electrochemical water splitting. Moreover, in the present work, the molar proportions of cobalt and iron were streamlined to study their synergistic effect on electrochemical HER and OER performance. The electrode of best-performing (CFP–S2) requires the lowest overpotentials of 242 mV for OER and 67.9 mV for HER at a current density of 10 mA/cm2, which maintains its activity after 24 h. The alkaline water splitting into a similar electrolytic bath using two electrode systems was demonstrated for 100 h with the lowest overpotential of 1.72 V. The remarkable electrochemical performance and postmortem analysis unambiguously demonstrate that CFP electrodes are a highly promising and robust option for long-duration water-splitting devices, and the facile SILAR method for scalable CFP electrode synthesis indicates enormous potential for commercial applications.

Crystallinity transformation engineering of hydrous cobalt nickel phosphate cathodes for hybrid supercapacitor devices: Extrinsic/battery to intercalation type pseudocapacitors

The necessitating strategies of rationalizing nanostructures and crystallinity of electrode material are crucial to developing high-efficiency hybrid energy storage devices. To enhance the energy storage performance of bimetal phosphates, it is important to have a strategic blend of metal cations that can work together synergistically. So, this work describes the scalable preparation of binder-free cobalt nickel phosphates thin film cathodes with cations variation (Co/Ni) via the facile Successive Ionic Layer Adsorption and Reaction (SILAR) process. The distinct roles of cations in cobalt nickel phosphate electrodes resulted in a noteworthy structural transformation from crystalline to amorphous with an increment of Ni content. The change in cations composition influences the pseudocapacitive performance from extrinsic/battery to intercalation type, and cobalt nickel phosphate electrode with an ideal cations composition (Co:Ni) ratio of approximately 1:1 attain the highest specific capacitance (SCs) of 2142 F g−1 (1071 C g−1). To fulfil the demand for high-performance hybrid supercapacitor devices, aqueous (HASC) and solid-state (HSSC) supercapacitors are assembled using optimized cobalt nickel phosphate (S-CNP5) as a cathode. The HASC device represents maximum SCs of 120 F g−1 with specific energy (SE) and specific power (SP) of 42.59 Wh kg−1 and 1600 W kg−1, respectively. The flexible HSSC device shows impressive SCs of 89 F g−1 and SE of 31.54 Wh kg−1 at SP of 2057.14 W kg−1. The practical demonstration of an HSSC device to power a 12-white LED lamp suggests that the SILAR strategy offers commercializing insights for fabricating high-specific capacity hydrous cobalt nickel phosphate thin film cathodes.

A Photoelectrochemical Sensor for the Sensitive Detection of Cysteine Based on Cadmium Sulfide/Tungsten Disulfide Nanocomposites.

In this work, a CdS-nanoparticle-decorated WS2 nanosheet heterojunction was successfully prepared and first used to modify ITO electrodes for the construction of a novel photoelectrochemical sensor (CdS/WS2/ITO). The thin-film electrode was fabricated by combining electrophoretic deposition with successive ion layer adsorption and reaction techniques. The results indicated that the synthesized heterojunction nanomaterials displayed excellent photoelectrochemical performance which was much better than that of pristine CdS nanoparticles and 2D WS2 nanosheets. Owing to the formation of the surface heterojunction and the effective interfacial electric field, the enhanced separation of photogenerated electron-hole pairs led to a remarkable improvement in the photoelectrochemical activity of CdS/WS2/ITO. This heterojunction architecture can protect CdS against photocorrosion, resulting in a stable photocurrent. Based on the specific recognition between cysteine and CdS/WS2/ITO, through the specificity of Cd-S bonds, a visible-light-driven photoelectrochemical sensor was fabricated for cysteine detection. The novel photoelectrochemical biosensor exhibited outstanding analytical capabilities in detecting cysteine, with an extremely low detection limit of 5.29 nM and excellent selectivity. Hence, CdS-WS2 heterostructure nanocomposites are promising candidates as novel advanced photosensitive materials in the field of photoelectrochemical biosensing.

Improved charge separation by anatase TiO2 nanorod arrays for efficient solid-state PbS quantum-dot-sensitized solar cells

To improve the charge separation and transporting between PbS/TiO2 interface in PbS quantum-dot-sensitized solar cells, a 400 nm length anatase TiO2 nanorod array was successfully prepared by the conversion from ZnO nanorod array immersed in a 75 mM ammonium hexafluorotitanate acid solution. The influence of different immersion time on the microstructure, crystal phase and light absorption of the anatase TiO2 nanorod arrays were systematically studied. The PbS quantum dots (QDs) were deposited on the anatase TiO2 nanorod array via spin-coating-assisted successive ionic layer absorption and reaction (spin-SILAR) procedure using 5 mM PbI2 precursor solution, 5 mM Na2S·9H2O solution and 1% EDT/ethanol (1/99, v/v) solution. The solid-state PbS QD-sensitized anatase TiO2 nanorod array solar cell with the structure of FTO/TiO2 compact layer/PbS QD-sensitized anatase TiO2 nanorod array/spiro-OMeTAD/Au was assembled for the first time, and the champion device exhibited a photoelectric conversion efficiency of 5.47% with an open-circuit voltage of 0.62 V, a short-circuit photocurrent density of 13.71 mA cm-2 and a fill factor of 64.28%.

A 2.4 V Aqueous Zinc-Ion Battery Enabled by the Photoelectrochemical Effect of a Modified BiOI Photocathode: Shattering the Shackle of the Electrochemical Window of an Aqueous Electrolyte.

Aqueous zinc-ion batteries emerge as a promising energy storage system with merits of high security, abundance, and being environmentally benign. But the low operating voltages of aqueous electrolytes restrict their energy densities. Previous reports have mostly focused on modifying the electrolytes to enlarge the operating voltages of aqueous zinc-ion batteries. However, either extra-expensive salts or potential safety hazards of organic additives are considered to be adverse for practical large-scale applications. Here, a proof-of-concept to enlarge the operating voltage of an aqueous zinc-ion battery by incorporating a well-designed semiconductor photocathode is proposed, which produces a photovoltage (Vph) across the semiconductor/liquid junction (SCLJ) interface to elevate the output voltage of zinc-ion battery under irradiation. The operating voltage of an aqueous zinc-ion battery can be markedly raised from 1.78 (thermodynamic limit) to 2.4 V when a BiOI nanoflake array photocathode with good surface modification is introduced, achieving a round-trip efficiency of 114.3% and a 34.8% increase of energy density compared to the theoretical value. The successive ionic layer adsorption and reaction modified surface effectively passivates surface trap defects of the BiOI photocathode and thus enlarges its Vph from 60 to 240 mV under irradiation. This study provides a design to enlarge the output voltages of aqueous zinc-ion batteries and other energy storage systems, providing insight into widening the voltage window, which is that the operating voltages are determined by photocathode under irradiation and not restricted by the electrochemical stability window of dilute aqueous electrolytes.

A novel photoelectrochemical phage sensor based on WO3/Bi2S3 for Escherichia coli detection

To achieve rapid detection of Escherichia coli, a photoelectrochemical phage sensor was constructed. WO3 and Bi2S3 composite nanomaterials were used as photosensitive materials, and Au nanoparticles were linked to T4 phage and modified on the electrode surface to achieve high sensitivity detection. Bi2S3 was modified on the surface of the WO3 electrode by successive ionic layer adsorption and reaction to form the heterojunction to reduce the complexation of electron-hole pairs. The sensor constructed with T4 phage as the recognition element has excellent recognition specificity and a lower detection limit, which compensates for the inability of other recognition elements to distinguish between live and dead bacteria. Various signal amplification techniques are flexibly combined to improve the photocurrent response before and after analyte identification, thereby improving the sensitivity of the sensor.